Laser industrial Chiller

LX Laser industrial Chiller

Models		1XJ-16F	1XJ-27F	1XJ-36F	1XJ-52F	1XJ-72F	1XJ-87F
Nominal Capacity	W	1600	2700	3600	5200	7200	8700
	Kcal/Hr	1376	2322	3096	4472	6192	29928
	Btu/Hr	5504	9288	12384	17888	24768	7482
Power source		220V~0HZ				3PH~80V~0HZ
Total input(W)		1126	1583	1953	2458	3310	3400
Refrigerant		R22
Power of pump		550	550	550	550	550	550
Flow range(L/min)		8-58	8-58	8-58	8-58	8-58	8-58
Lift range(m)		26-16	26-16	26-16	26-16	26-16	26-16
Pure water storage(L)		16	20	22	22	27	27
Max air volume(m3/h)		830	1700	3110	3110	4235	4235
Lolw switch		Work flow≥5L/min,break flow≤3.5/min,allow current≤3A
Chilled Water inlet(Rp)		1/2	1/2		3/4	3/4	3/4
Chilled Water (Rp) outlet		1/2	1/2	3/4	3/4	3/4	3/4
Drain(Rp)		1/2	1/2	1/2	1/2	1/2	1/2
L×W×H(mm)		450×650×75	490×700×825	530×750×925	530×750×925	580×820×1045	580×820×1045

Features:

LXJ-xxF Series laser lndustrial chiller can be installed easily and it is
suitable for YAG lsaer equipments,such as laser marker,laser cutter,laser welder,laser driller,laser wire-cutter etc.With cooling capacity from 1.6KW to 8.7KW.

Industrial water chiller for attention
1, unit run-time power supply voltage must be stable, considering all factors, blood pressure, the work crew to maintain the rated voltage of less than + -10%, voltage too high or too low are the adverse effects of the crew.
2, power frequency should be maintained at rated + -2%.
3, for the protection of human security, if the body leakage avoid the risk of electric shock, Shell should have a good crew, reliable ground fault protection device has been accidents, according to strict regulations require construction electrician.
4, transportation or move out room, do not impact with the ground, causing too much impact.
5, the room should have sufficient space for the installation and maintenance unit, taking into account the adequate space extubation.
6, the installation of the selected sites:
①, avoid direct sunlight installations or other heat source will be directly radiation areas.
②, from power nearly facilitate wiring.
③, solid ground strength, and the noise does not easily cause resonance of places.
④, placed in the house, choose a well-ventilated, humidity small, less suitable places.

7, to facilitate the discharge cooling water and chilled water, basic units must be installed around the gutter.
8, chilled water and cooling water undesirable not only led to the scaling of heat transfer, heat transfer efficiency from lower and the weakening performance unit will heat pipe corrosion caused major accidents, customers should be in strict accordance with the GB50050-1995 "Design of industrial circulating cooling water treatment norms "at the request of water treatment.
9, vertical flow switch should be installed in the outlet pipe into the pipes or the level of the paragraph.
10, flow switch to the direction of flow at least six times the pipeline diameter of straight pipe section; flow switch to the direction of flow at least four times the diameter of straight pipe pipeline paragraph; should not be installed in the near Bend, in the vicinity of the valve orifice and .
11, in order to prevent flow switch trembled, the water system should be all of the gas emissions out.
12, Australian customs regulation flowmeter, it is lower than the minimum flow of water in a state separate from the flow. When the water flow to meet the requirements, flow switch should remain closed state.


Specifications:low noise ,high reliability,low vibration,high efficiency
Export Markets:millde east; south america;africa
various compressors  is used for air-conditioner as a replacement parts ,and they are high quality and excellent matching.